Echelon NodeUtil Node Utility Manual de usuario Pagina 28
- Pagina / 40
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
22 Using NodeUtil
variable index). The data from the last network variable update to the selected
network variable is displayed.
At the prompt, enter the data to be sent to the network variable, in hexadecimal
bytes. Separate each pair of hexadecimal digits with a space, and enter all the
required data on one line. The data values for any bytes that you do not enter
after the first character default to zero. For example, you can enter 01 00 00 or
just enter 1 to set a SNVT_switch_2 input network variable to the on state.
Press ENTER without any characters to cancel the update so that the input
value is not changed.
You can use the Set the (D)omain of the network interface command to configure
the NodeUtil network interface with a domain and authentication key to match
those of the destination device if the network variable has been configured as
authenticated.
V – Control Verbose Modes
Use this command to enable or disable two verbose modes: for network interface
messages and for network traffic. These modes are useful for debugging network
problems. By default, network interface message verbose mode is off, and
network traffic verbose mode is on.
If you enable verbose mode for network interface messages, NodeUtil displays the
contents of all application buffers going to and coming from the NodeUtil network
interface.
If you enable verbose mode for network traffic, any incoming message addressed
to the application processor on the network interface is displayed.
W – Write Device Memory
Use this command to write to the memory of the selected device. You can specify
the starting address in hexadecimal format. The contents of the memory address
that you specify are displayed in hexadecimal. Enter a new value for the location
in hex and then press the ENTER key, or press the ENTER key with no data to
leave the value unchanged. To stop entering data, enter any value that is not a
hexadecimal character, such as a period (.), and press ENTER.
If you change any of the data in memory, you are given the opportunity to update
both the application and configuration checksums, or just the configuration
checksum.
Important: The device should be in the applicationless state before you change
any of the application image memory, otherwise the device will report an
application checksum error. Similarly, the device should be in the applicationless
or unconfigured state before you change any of the network image memory,
otherwise the device will report a configuration checksum error.
X – Create Device Interface (XIF) File
Use this command to create a version 3 device interface file (.xif extension) for
the selected device. You can enter a file name for the XIF file. If the device has
an alphanumeric program ID, this ID is the default filename. You can use the
- NodeUtil Node Utility 1
- User’s Guide 1
- ONMARK, LonTalk, LONWORKS 2
- Welcome 3
- Audience 3
- Related Documentation 3
- ONWORKS platform 4
- Table of Contents 5
- Introduction 7
- Requirements 8
- PC Hardware Requirements 8
- PC Software Requirements 9
- Using NodeUtil 11
- Starting NodeUtil 12
- Command-Line Parameters 12
- Using a Script File with 14
- NodeUtil 14
- The NodeUtil Main Menu 15
- A – Add Device to List 16
- F1 – Show Banner 16
- E – Exit this Application 17
- G – Go to Device Menu 18
- H – Help with Commands 18
- L – Display Device List 18
- R – Reboot 3150 Device 19
- T – Transceiver Parameters 19
- V – Control Verbose Modes 20
- W – Wink a Device 20
- The NodeUtil Device Menu 21
- A – Node Address Table 22
- B – Buffer Configuration 23
- K – Check Neuron Executable 25
- L – List Network Variables 25
- W – Write Device Memory 28
- – Performance Test 29
- = – Signal Strength 30
- * – Refresh Memory 30
- – Redirect Input from a File 30
- Example 1 31
- Example 2 32
- Example 3 33
- License Agreement 35
Relacionado con productos y manuales para Hardware Echelon NodeUtil Node Utility
Hardware Echelon FTXL Hardware Manual de usuario
(92 paginas)
(92 paginas)
Hardware Echelon FTXL Manual de usuario
(261 paginas)
(261 paginas)
Airaid 510-622 manuals
Owner’s manuals and user’s guides for Accessories for air Airaid 510-622.
We providing 1 pdf manuals Airaid 510-622 for download free by document types: User Manual
Airaid 510-622 User Manual (2 pages)
Brand: Airaid | Category: Accessories for air | Size: 0.19 MB |
Table of contents
More products and manuals for Accessories for air Airaid
| Models | Document Type |
|---|---|
| 510-624 |
User Manual
Airaid 510-624 User Manual,
2 pages
|
| 510-628 |
User Manual
Airaid 510-628 User Manual,
2 pages
|
| 520-505 |
User Manual
Airaid 520-505 User Manual,
2 pages
|
| 520-538 |
User Manual
Airaid 520-538 User Manual,
2 pages
|
| 520-605 |
User Manual
Airaid 520-605 User Manual,
2 pages
|
| 530-572-P |
User Manual
Airaid 530-572-P User Manual,
2 pages
|
| 530-578-P |
User Manual
Airaid 530-578-P User Manual,
2 pages
|
| 530-632 |
User Manual
Airaid 530-632 User Manual,
2 pages
|
| 540-539-P |
User Manual
Airaid 540-539-P User Manual,
2 pages
|
| 860-161 |
User Manual
Airaid 860-161 User Manual,
2 pages
|
| 800-504 |
User Manual
Airaid 800-504 User Manual,
2 pages
|
| 860-341 |
User Manual
Airaid 860-341 User Manual,
2 pages
|
| 860-348 |
User Manual
Airaid 860-348 User Manual,
2 pages
|
| 860-425 |
User Manual
Airaid 860-425 User Manual,
2 pages
|
| 861-341 |
User Manual
Airaid 861-341 User Manual,
2 pages
|
| 200-700 |
User Manual
Airaid 200-700 User Manual,
2 pages
|
| 200-712 |
User Manual
Airaid 200-712 User Manual,
2 pages
|
| 200-783 |
User Manual
Airaid 200-783 User Manual,
2 pages
|
| 200-719 |
User Manual
Airaid 200-719 User Manual,
2 pages
|
| 200-785 |
User Manual
Airaid 200-785 User Manual,
2 pages
|
© 2020, manymanuals.es. Todos los derechos reservados | 0.070 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales