Echelon LonPoint Application and Plug-In Manual de usuario Pagina 164
- Pagina / 191
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
12-4 Type Translator Functional Block
variable type also controls whether the data in the
mapping table is interpreted as signed or unsigned.
Scaling Sets scaling for network variable values. The value
read from the input network variable is multiplied by
the
Multiply field value and then added to the Add
field value. When an input or output type is changed,
the scaling values revert to their defaults.
Once the network variable types of the input and
output network variables have been set, changing the
type of either of them resets this property to its
defaults. The default for the Add field is 0; the default
for the Multiply field depends on the scaling factors of
the input and output network variable types.
The type translator plug-in does not display any
units. Any values entered must correspond to the
native units of the corresponding network variable
type (normally SI units), if there are any. The Scaling
values are associated with the
Data_In network
variable.
Mapping Maps one value to another value. To use mapping,
you must select the
Enabled option. If this option is
selected, each input value (0-15) will be mapped to
the output value in the associated field. If the input
value is outside of the range 0-15, then the mapping
corresponding to the nearest value is used.
Fractional input values will be truncated to compute
the index (i.e. 4.99 will be truncated to 4; if you wish
to have values rounded to the nearest integer value,
use the Scaling option to add .49 to each value). The
map table entries are entered and displayed as signed
byte values (-128 to 127). However, if the
Signed
setting of Data Output is cleared, these values will be
interpreted as unsigned byte values (0 to 255), so the
values –128 to –1 internally map to the values 128 to
255.
Once the network variable types of the input and
output network variables have been set, changing the
type of either of them disables mapping.
The type translator plug-in does not display any
units. Any values entered must correspond to the
native units of the corresponding network variable
type (normally SI units), if there are any. The
Mapping values are associated with the
Data_Out
network variable
Set Default When this option is set,
Scaling and Mapping
values are automatically selected to convert the
Data_In network variable type to the Data_Out
network variable type. This is done automatically
every time you change a type, so normally you will
- LonPoint 1
- Application 1
- Contents 3
- LonPoint System Overview 7
- 1-2 LonPoint System Overview 8
- Getting Started 10
- LonPoint Applications 10
- LONMARK Certified: Yes 11
- Upstream and Downstream 12
- Heartbeats 12
- Throttle 13
- Default Values 13
- Override Values 13
- Network Variables 14
- ONMARK Reference help file.) 15
- Network Variable Formats 16
- 1-12 LonPoint System Overview 18
- The Digital Input Functional 19
- Digital Input 21
- Delayed Processing option 23
- Pulsed or the One-Shot 23
- XX (e.g. 2.XX) 24
- The Digital Input/Counter 27
- Functional Block: Application 27
- SNVT_temp_f 28
- Digital Input/Counter 29
- Processing Options 30
- One-Shot 31
- Repeating Count 32
- Can Counter 33
- Boxing Machine 33
- Frequency 34
- Processing Parameters 35
- Translation 36
- Output Parameters 37
- The Digital Output Functional 39
- Digital Output 41
- Input Defaults 44
- Mode network 45
- Hand-Off-Auto switch 48
- SNVT_hvac_mode 50
- Digital Encoder, Lookup 50
- Digital Encoder 51
- Lookup Tables 52
- Mode_Out 54
- The Analog Input Functional 57
- Analog Input, Translation 58
- Analog Input 59
- Ω RTD measures 0.12º C at the 60
- The Analog Output Functional 67
- Configuring an Analog Output 68
- Analog Output 69
- Defaults 70
- The AFB Functional Block: 73
- Application and Plug-in 73
- Analog Function Block 75
- Function 78
- The PID Controller Functional 85
- Enable network variable 88
- PID Coefficients 91
- Cascade – 100
- Reverse Acting process 101
- The Scheduler Functional 103
- Blocks: Application and the 103
- LonPoint Schedule Maker 103
- SetTime Time 104
- SCH- 1 Clock 104
- SCH- 1 Event Scheduler 105
- SCH- 1 State Machine 105
- Types of Schedules 107
- Defining Daily Schedules 108
- Daily Schedule 109
- Default Daily Schedule 110
- Defining Inputs and Outputs 111
- 10-10 Scheduler Interface 112
- Digital Inputs 113
- Digital Outputs 114
- 10-14 Scheduler Interface 116
- Defining State Transitions 117
- 10-16 Scheduler Interface 118
- State Transition Definitions 119
- Defining Exit Conditions 120
- Exit Condition Definitions 121
- 10-20 Scheduler Interface 122
- Configuring Daily Schedules 124
- 10-24 Scheduler Interface 126
- Configuring a State Machine 128
- Assigning Input/Output Names 128
- 10-28 Scheduler Interface 130
- Defining the State Machine 131
- 10-30 Scheduler Interface 132
- 10-32 Scheduler Interface 134
- Setting Scheduler Options 135
- 10-34 Scheduler Interface 136
- 10-36 Scheduler Interface 138
- Resetting the Simulator 139
- Using Debug Mode 139
- Simulating Inputs 140
- Running to the Next Event 140
- Overriding the Event Schedule 141
- 10-40 Scheduler Interface 142
- Setting the SCH-10 Time 144
- Testing a Schedule Design 145
- 10-44 Scheduler Interface 146
- The Schedule Keeper Utility 147
- Modifying the Daily Schedules 149
- 11-4 Schedule Keeper Utility 150
- Schedule 151
- Modifying Schedule Overrides 152
- Modifying System Parameters 153
- Adding Schedule Constraints 154
- Schedule Constraint Equations 155
- Operands 156
- Operators 156
- Examples: 156
- Adding Parameter Constraints 157
- Converting to US Units 159
- 11-14 Schedule Keeper Utility 160
- Data_In and Data_Out network 162
- Type Translator and Status 162
- Type Translator 163
- Scaling or Mapping values 165
- The Data Logger Functional 167
- Block: Application, Plug-in 167
- SNVT_str_asc 168
- SNVT_switch 168
- Data Logger 169
- Input Options 170
- Input Limits 171
- Log High 172
- Log Options 173
- Data network variable 174
- Attributes 174
- Data Logger Selection 177
- Menu Commands 178
- Formatting Preferences 179
- Monitoring Preferences 180
- Log Preferences 181
- Data Log list and select 182
- CSV Text File Format 183
- Tagname Line 183
- Data Lines 184
- Data Point Formats 185
- Command Line Switches 185
- The Node Object Functional 188
- ONMARK aware network tools 189
- Status network 190
Relacionado con productos y manuales para Hardware Echelon LonPoint Application and Plug-In
(24 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.071 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales