Echelon LonPoint Application and Plug-In Manual de usuario Pagina 34
- Pagina / 191
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
3-8 Digital Input/Counter Functional Block
Frequency
Measures the frequency of the input signal in the range of 1Hz to 20kHz.
Minimum resolution of the frequency measurement is <0.5% over the full
measurement range. The Analog network variable reports the instantaneous
measured frequency or a translated representation of it. The Digital network
variable is not used with this processing option.
On startup the Analog output network variable is not immediately available as
the input is auto-ranged. This process takes up to four seconds.
The frequency measurement may be modified using a translation table. The
translation table operates in the same manner as the translation table in the
Analog input functional block found in the AI-10 LonPoint Module. The
translation table is in turn followed by a filtering function. The filter averages
over N samples, where N is the configured filter length. The supported range of
N is 1 to 255. The equivalent filter time constant for this range is approximately
0.5 seconds to 50 seconds. No filtering is done if N equals 1.
If no translation is applied, an appropriate network variable type for the Analog
output network variable in this mode is
SNVT_freq_f. If translation is applied
then the appropriate floating point SNVT for the process variable being
measured should be used (e.g.
SNVT_flow_f).
The input cannot be configured for dry contact when the frequency processing
option is selected. Debounce is not supported. The hardware input may be
configured for voltage input (5V, 12V, 24V, or 31V only).
Using The Control Network Variable
The Control network variable can be driven from another device on the network
or an HMI application. It is sequenced in a way that allows count values to be
sampled while continuing to count without interruption. It applies to the Count,
Repeating Count, and On Time processing options. The
Control network
variable type is
UNVT_count_control.
The following summarizes the input values to the
Control network variable:
RUN Enables event counting. The count value is output to
the
Analog network variable. The send-on-delta value
is used to throttle the network variable, so the
network variable is not necessarily propagated with
every count.
CLEAR Copies the internal count to the Analog network
variable and then clears the internal count. Events
continue to be counted, but the
Analog network
variable is not updated. This allows an HMI
application to read the
Analog network variable
while the
Control network variable is set to CLEAR.
The HMI application can set the
Control network
variable to
RUN after reading the Analog network
variable.
- LonPoint 1
- Application 1
- Contents 3
- LonPoint System Overview 7
- 1-2 LonPoint System Overview 8
- Getting Started 10
- LonPoint Applications 10
- LONMARK Certified: Yes 11
- Upstream and Downstream 12
- Heartbeats 12
- Throttle 13
- Default Values 13
- Override Values 13
- Network Variables 14
- ONMARK Reference help file.) 15
- Network Variable Formats 16
- 1-12 LonPoint System Overview 18
- The Digital Input Functional 19
- Digital Input 21
- Delayed Processing option 23
- Pulsed or the One-Shot 23
- XX (e.g. 2.XX) 24
- The Digital Input/Counter 27
- Functional Block: Application 27
- SNVT_temp_f 28
- Digital Input/Counter 29
- Processing Options 30
- One-Shot 31
- Repeating Count 32
- Can Counter 33
- Boxing Machine 33
- Frequency 34
- Processing Parameters 35
- Translation 36
- Output Parameters 37
- The Digital Output Functional 39
- Digital Output 41
- Input Defaults 44
- Mode network 45
- Hand-Off-Auto switch 48
- SNVT_hvac_mode 50
- Digital Encoder, Lookup 50
- Digital Encoder 51
- Lookup Tables 52
- Mode_Out 54
- The Analog Input Functional 57
- Analog Input, Translation 58
- Analog Input 59
- Ω RTD measures 0.12º C at the 60
- The Analog Output Functional 67
- Configuring an Analog Output 68
- Analog Output 69
- Defaults 70
- The AFB Functional Block: 73
- Application and Plug-in 73
- Analog Function Block 75
- Function 78
- The PID Controller Functional 85
- Enable network variable 88
- PID Coefficients 91
- Cascade – 100
- Reverse Acting process 101
- The Scheduler Functional 103
- Blocks: Application and the 103
- LonPoint Schedule Maker 103
- SetTime Time 104
- SCH- 1 Clock 104
- SCH- 1 Event Scheduler 105
- SCH- 1 State Machine 105
- Types of Schedules 107
- Defining Daily Schedules 108
- Daily Schedule 109
- Default Daily Schedule 110
- Defining Inputs and Outputs 111
- 10-10 Scheduler Interface 112
- Digital Inputs 113
- Digital Outputs 114
- 10-14 Scheduler Interface 116
- Defining State Transitions 117
- 10-16 Scheduler Interface 118
- State Transition Definitions 119
- Defining Exit Conditions 120
- Exit Condition Definitions 121
- 10-20 Scheduler Interface 122
- Configuring Daily Schedules 124
- 10-24 Scheduler Interface 126
- Configuring a State Machine 128
- Assigning Input/Output Names 128
- 10-28 Scheduler Interface 130
- Defining the State Machine 131
- 10-30 Scheduler Interface 132
- 10-32 Scheduler Interface 134
- Setting Scheduler Options 135
- 10-34 Scheduler Interface 136
- 10-36 Scheduler Interface 138
- Resetting the Simulator 139
- Using Debug Mode 139
- Simulating Inputs 140
- Running to the Next Event 140
- Overriding the Event Schedule 141
- 10-40 Scheduler Interface 142
- Setting the SCH-10 Time 144
- Testing a Schedule Design 145
- 10-44 Scheduler Interface 146
- The Schedule Keeper Utility 147
- Modifying the Daily Schedules 149
- 11-4 Schedule Keeper Utility 150
- Schedule 151
- Modifying Schedule Overrides 152
- Modifying System Parameters 153
- Adding Schedule Constraints 154
- Schedule Constraint Equations 155
- Operands 156
- Operators 156
- Examples: 156
- Adding Parameter Constraints 157
- Converting to US Units 159
- 11-14 Schedule Keeper Utility 160
- Data_In and Data_Out network 162
- Type Translator and Status 162
- Type Translator 163
- Scaling or Mapping values 165
- The Data Logger Functional 167
- Block: Application, Plug-in 167
- SNVT_str_asc 168
- SNVT_switch 168
- Data Logger 169
- Input Options 170
- Input Limits 171
- Log High 172
- Log Options 173
- Data network variable 174
- Attributes 174
- Data Logger Selection 177
- Menu Commands 178
- Formatting Preferences 179
- Monitoring Preferences 180
- Log Preferences 181
- Data Log list and select 182
- CSV Text File Format 183
- Tagname Line 183
- Data Lines 184
- Data Point Formats 185
- Command Line Switches 185
- The Node Object Functional 188
- ONMARK aware network tools 189
- Status network 190
Relacionado con productos y manuales para Hardware Echelon LonPoint Application and Plug-In
(24 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.073 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales