Echelon SmartServer 2.2 Manual de usuario Pagina 515
- Pagina / 560
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
516 Appendix B – Using the SmartServer Console Application
Command
Description
ip852chanmode mode
Displays the IP-852 channel mode or sets it to one of the following
values:
1 - Backward Compatible (required for the i.LON 1000 and LNS
3). You must enable this option if your channel will contain any
i.LON 1000’s or LNS 3 LONWORKS/IP interfaces. This causes the
SmartServer to operate using a protocol that is compatible with
these devices, but is not strictly EIA-852 compliant. In backward
compatible mode, you can use a maximum of 40 devices. You can
only have one device located behind each NAT firewall, and you
cannot have duplicate IP addresses or duplicate port assignments.
2 - Standard EIA-852. Select this option when using a standard
LONWORKS IP-852 channel. When using this mode, you can only
have one device located behind each NAT firewall. You can use
up to 256 devices per channel in this mode. The IP address
(including the port assignment) must be unique. This is the
default.
3 - Extended Firewall Support. This option is recommended
whenever your IP-852 channel crosses an IP firewall, whether or
not the firewall is using Network Address Translation (NAT).
Depending on the particular firewall and its configuration, this
option may be required. In addition, this will allow you to place
more than one IP-852 device behind an NAT firewall, and to
create multiple OpenLNS LONWORKS/IP interfaces in the same
channel using the same IP address (but with different ports).
Without this option, only one device may reside behind a NAT
firewall, and all devices on the channel must have unique IP
addresses. This option extends the EIA-852 protocol in a way that
is not strictly compliant with that standard, though it should still be
compatible with other EIA-852 devices. You can use up to 256
devices per channel in this mode.
ip852port portnumber
Sets the local IP port for the IP-852 router.
linkstats [all|clear]
Reports or clears the following LonTalk link statistics:
Trans pkts. Number of packets transmitted.
Recvd pkts. Number of packets received
Trans errs. Number of transmission errors.
RecvPrPkcts. Number of packets received from a retry.
Collsions. Number of packet collisions.
MissedPkts. Number of missed packets.
listapp
Lists the current application instances.
logout
Terminates a Telnet session
ltipport
Reserved.
mkdir directory
Makes a directory.
nataddress address
Sets the external NAT address to be used when the SmartServer is used
as an IP-852 router and is installed behind a NAT firewall.
ping hostaddr
Tests communications to another IP host. This command accepts both
IPv4 and IPv6 network addresses.
- SmartServer 2.2 1
- User’s Guide 1
- 1
- Chips, and other OEM 2
- Chips in such applications 2
- Preface 10
- Purpose 11
- Audience 11
- Requirements 11
- SmartServer Documentation 12
- Related Reading 13
- Content 13
- Using Technical Support 16
- Introduction 18
- SmartServer Limits 22
- Services and Tools 22
- 24 Introduction 23
- Installation Overview 25
- Configuring and Managing the 36
- Connecting the SmartServer 38
- Configuring the SmartServer 41
- ONWORKS database to open 42
- Configuring Time Properties 48
- Using HTTPS/SSL 53
- Rebooting the SmartServer 55
- Creating Modem Connections 56
- Selecting Modem Type 57
- Adding Host Devices 64
- ONWORKS/IP servers to 67
- Using an IP-852 Channel 91
- ONWORKS network interface 97
- SmartServer RNI Limits 99
- Managing the SmartServer 101
- Testing Connections 109
- Replacing the SmartServer 120
- ONWORKS network 127
- ONWORKS connections 130
- ONWORKS, Modbus, or M-Bus 130
- ONWORKS DATA point: 133
- ONWORKS data 135
- ONWORKS devices, and 137
- ONWORKS network variable 137
- ONWORKS Network Variables 138
- ONWORKS Devices 138
- Managing Network Objects 143
- Managing Channel Objects 146
- ONWORKS 148
- Managing Device Objects 149
- ONWORKS connections in the 152
- Managing Data Point Objects 155
- LONWORKS 157
- Using Device Templates 160
- ONWORKS Data Points 161
- Adding Connections 173
- Temperature 174
- Room Controller 174
- ONWORKS Connections 176
- Configuring Connections 179
- Deleting Connections 181
- Validating Connections 182
- Adding File Attachments 184
- Deleting File Attachments 185
- Retrieving File Attachments 186
- Viewing Connections 186
- Configuring Global Settings 189
- Management Tool 194
- Network Management Overview 195
- Network Management Scenarios 195
- Echelon Enterprise 197
- Services 2.2 197
- Designing a LONWORKS Network 198
- ONWORKS Network 203
- Using Standalone Mode 207
- Database 208
- LNS Proxy 209
- Web Service 209
- SmartServer 209
- ONWORKS channels 215
- Creating a LONWORKS Channel 225
- ONWORKS Channels 226
- ONWORKS channel is 60 228
- Creating LONWORKS Devices 230
- Configuring LONWORKS Devices 232
- and then 236
- Viewing LONWORKS Devices 241
- ONWORKS channel on which the 242
- Creating LONWORKS Routers 246
- Configuring LONWORKS Routers 249
- Creating Functional Blocks 252
- Viewing Functional Blocks 255
- Viewing LONWORKS Data Points 266
- Designing a Modbus Network 269
- Configuring Modbus Channels 270
- This is the default 272
- Creating Modbus Devices 273
- Configuring Modbus Devices 275
- Viewing Modbus Devices 276
- Creating Modbus Data Points 277
- Viewing Modbus Data Points 282
- Designing an M-Bus Network 285
- Creating M-Bus Channels 286
- Configuring M-Bus Channels 286
- Creating M-Bus Devices 288
- Configuring M-Bus Devices 289
- ONWORKS Neuron ID). Enter a 290
- Viewing M-Bus Devices 291
- Creating M-Bus Data Points 293
- Viewing M-Bus Data Points 295
- Using the Virtual Channel 297
- Installing LONWORKS Networks 299
- Acquiring the Neuron ID 300
- Selecting Devices 306
- Installing Devices 307
- Checking Device Status 308
- Installing Routers 310
- Loading Device Applications 312
- Replacing Devices 316
- Manually Replacing Devices 319
- Decommissioning Devices 320
- Testing Devices 322
- Querying Devices 323
- Winking Devices 325
- 3. Click Submit 326
- Alarming 328
- Alarming Overview 329
- ONWORKS alarming device 330
- Selecting a Data Point 333
- Selecting a Compare Point 333
- Entering a Constant Value 334
- . When a hysteresis 337
- Configuring Alarm Conditions 346
- Scheduling 356
- Scheduling Overview 357
- Creating an Event Scheduler 357
- Planning Your Schedule 358
- Selecting Data Points 366
- Creating Daily Schedules 369
- Creating One-Time Exceptions 374
- Creating Exception Groups 386
- Editing Exceptions 388
- Editing Exception Groups 389
- Night Schedule 395
- Creating the Night Schedule 399
- 402 Scheduling 401
- Using the Event Calendar 402
- Data Logging 410
- Data Logging Overview 411
- Creating a Data Logger 411
- Setting Alarm Limits 419
- Attaching a Log File 424
- Triggering Log Transfer 425
- Viewing Data Logs 429
- Viewing Data Points 431
- Connecting Pulse Meters 437
- Selecting Input Points 451
- Selecting an Output Point 455
- Using Type Translators 458
- Type Translator Overview 459
- Creating a Type Translator 459
- Opening a Type Translator 460
- ONWORKS data points. See 464
- 16xSNVT_switch_TO_SNVT_state 465
- Merge SNVT Setting 465
- SNVT_scene_TO_SNVT_setting 466
- SNVT_scene_TO_SNVT_switch 466
- SNVT_setting_TO_SNVT_switch 467
- SNVT_state_TO_16xswitch 467
- SNVT_switch_TO_SNVT_lev_desc 467
- Split SNVT Setting 468
- Installing an M-Bus Device 475
- ONWORKS data point 476
- Specifying a Delay 478
- 480 Using Type Translators 479
- Using the SmartServer with 480
- OpenLNS CT 480
- ONWORKS connections to 489
- Appendix A 504
- Troubleshooting 505
- Appendix B 508
- Application 508
- Console Command List 509
- The Bootrom State 517
- Updating the Bootrom 517
- Appendix C 520
- Securing the SmartServer 520
- Setting Access Restrictions 522
- Locations 524
- Aliases 526
- Parameters 526
- Sample WebParams.dat file 527
- Securing Folders and Files 528
- Securing Files 529
- Example 1 530
- Example 3 530
- Example 4 531
- Example 5 531
- Example 6 532
- Figure 9c— Setup for realms 539
- Appendix D 540
- SmartServers 540
- Network 544
- Networks 546
- Appendix E 552
- Software License Agreements 552
Relacionado con productos y manuales para Sensores Echelon SmartServer 2.2
Sensores Echelon IP-852 Channel Manual de usuario
(56 paginas)
(56 paginas)
Sensores Echelon i.LON SmartServer 2.0 Manual de usuario
(443 paginas)
(443 paginas)
Sensores Echelon i.LON SmartServer 2.0 Manual de usuario
(266 paginas)
(266 paginas)
Sensores Echelon LonPoint Module Manual de usuario
(115 paginas)
(115 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.115 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales